Makita BL7010 7.2V Lithium-Ion 1.0Ah

Makita BL7010 7.2V Lithium‑Ion 1.0Ah — Lightweight power for precision tasks

The BL7010 is a compact 7.2V, 1.0Ah lithium‑ion battery designed for ultra‑portable Makita tools such as select 7.2V screwdrivers and drivers. It prioritizes low weight and quick charging for repetitive, light-duty work in tight spaces.

Key specs

Voltage	7.2V
Capacity	1.0Ah (≈7.2Wh)
Chemistry	Lithium‑ion
Approx. charge time	~30 minutes with Makita DC07SA charger
Protection	Star Protection Computer Controls (overload, over‑discharge, overheating)
Compatibility	Makita 7.2V Li‑Ion tools specified for BL7010/BL0715 (e.g., select DF010D/TD020D series). Not compatible with Makita 12V max CXT or older 7.2V Ni‑Cd/Ni‑MH tools.

Best for

• Light fastening, electronics assembly, cabinetry hardware, and trim where precise control matters.
• Service calls and overhead work that benefit from minimal tool weight.
• Short, intermittent tasks with frequent battery swaps.

Consider alternatives if

• You need longer runtime on the same tools: consider the Makita BL0715 (1.5Ah).
• You drive large fasteners or drill frequently: move up to Makita 12V max CXT or 18V LXT platforms.
• Your tool uses Ni‑Cd/Ni‑MH 7.2V or any slide‑style 12V battery: the BL7010 will not fit.

Runtime expectations

With 7.2Wh of energy, expected runtime varies by task and tool load:

• Light-duty fastening (average draw ~10W): roughly 30–40 minutes of active trigger time.
• Moderate fastening (average draw ~20W): roughly 15–20 minutes.
• Heavier continuous load (~30W): roughly 10–12 minutes.

Tip: Keep two batteries and rotate them; the ~30‑minute charge time often matches typical usage cycles for light assembly work.

Charging and care

• Use only the Makita DC07SA (or charger specified in your tool manual).
• Allow the pack to cool before charging; avoid charging when hot from use.
• Store in a cool, dry place at ~40–60% charge if unused for a month or more.
• Keep terminals clean and protect from metal objects that could short the contacts.
• Operate and charge within typical room temperatures for best performance; avoid extreme heat/cold.

Pros and cons

• Pros: Very light, fast charging, excellent tool balance for precision tasks, built‑in electronic protections.
• Cons: Lower capacity than BL0715, limited to compatible 7.2V Li‑Ion tools, not ideal for heavy-duty work.

Compatibility notes

Check your tool’s model plate or manual for BL7010/BL0715 compatibility. This pack does not fit Makita 12V max CXT or 18V LXT tools and is not interchangeable with older 7.2V Ni‑Cd/Ni‑MH batteries.

FAQ

Will this battery work in any Makita 7.2V tool?

No. It fits only Makita 7.2V Li‑Ion tools designed for the BL7010/BL0715 form factor (e.g., select DF010D/TD020D). It won’t fit 7.2V Ni‑Cd/Ni‑MH tools or 12V/18V platforms.

Which charger should I use?

Use the Makita DC07SA or the charger specified in your tool’s manual. Using an incompatible charger can damage the pack or create a safety hazard.

How does this compare to the BL0715?

The BL0715 is 1.5Ah (about 50% more runtime) with similar size/fit. Choose BL0715 for longer sessions; choose BL7010 to minimize weight and cost.

Can I leave the battery on the charger?

Unplug after it reaches full to reduce heat exposure and prolong life. Modern chargers manage maintenance charging, but minimizing time at 100% in warm conditions helps longevity.

What’s the expected lifespan?

Typical Li‑ion packs last a few hundred cycles. Avoid deep discharges, extreme temperatures, and high‑heat storage to maximize lifespan.