Arlo Camera Mounts

Arlo camera mounts help you place and aim your cameras for clear footage and fewer blind spots. Pick a mount that matches your camera’s interface and your surface (drywall, wood, brick) for a stable, weather‑ready setup.

Choose the Right Mount

• Magnetic quick‑release: Fast repositioning and tool‑free aiming. Use if you move cameras often or mount under eaves; avoid in high‑theft areas unless elevated or supplemented with a tether.
• Screw/ball‑joint wall or ceiling: Most secure and most adjustable. Use for permanent outdoor installs and precise angles; avoid if you can’t drill.
• Heavy‑duty outdoor: Longer arms and stronger joints for windy areas or wider offsets; ensure the arm supports your camera’s weight.
• Clamp/gutter/fence: No‑drill installs on gutters, rails, or poles. Use for rentals; check tightness after storms.
• Adhesive/no‑drill plates: Quick indoor use on smooth surfaces. Avoid on textured paint, brick, or where heat/cold could weaken adhesion.

Compatibility Checklist

• Mounting interface: Check your camera for a 1/4"‑20 threaded insert (fits universal screw mounts) or a smooth magnetic back/puck (needs the matching Arlo magnetic mount).
• Model notes: Many Arlo wire‑free models support 1/4"‑20 or Arlo magnetic mounts. Arlo video doorbells typically use a doorbell‑specific bracket and are not compatible with camera mounts.
• Surface & hardware: Drywall needs anchors; brick/concrete needs masonry anchors. Use stainless or galvanized screws outdoors.
• Clearance: Ensure enough space to tilt/rotate without the camera housing hitting soffits or walls.

Placement Tips for Better Video

• Height: 7–9 ft above ground, angled 15–30° downward for faces and plates without sky glare.
• Coverage: Aim across entry paths rather than straight on; avoid pointing directly at windows, bright lights, or moving tree branches.
• Signal: Test Wi‑Fi/Base Station signal in the app before drilling. Relocate or add a SmartHub/extender if the signal is weak.
• Weather: Mount under eaves when possible. Keep lenses out of direct rain and sun to reduce droplets and lens flare.

Install Steps (10–20 minutes per mount)

1. Mark location: Hold the base, check camera view in the app, and mark holes.
2. Drill: Use a wood bit for studs; use a masonry bit and anchors for brick/concrete. Wear eye protection.
3. Secure base: Drive screws until snug (do not overtighten plastic bases).
4. Attach camera: Snap to magnetic mount or thread onto the 1/4"‑20 stud, then tighten the collar.
5. Fine‑tune aim: Open the live view and adjust angle; lock joints firmly.

Outdoor Durability & Care

• Choose mounts labeled weather‑resistant; confirm operating temperature and corrosion resistance if you’re coastal or high‑heat.
• Recheck screws and joints monthly and after storms or big temperature swings.
• If using a power cable, create a drip loop and route under eaves; seal exterior holes with outdoor‑rated caulk.

Pack Sizes & Accessories

• Single or two‑packs: Add a mount where you need a new angle.
• Multi/bulk packs: Cost‑effective for multi‑camera homes or small businesses.
• Helpful add‑ons: Extension arms for tricky angles, security tethers/anti‑theft screws, and extra anchors for masonry.

Pros and Cons by Type

• Magnetic: Pros—fast, clean look. Cons—easier to remove; may shift in strong wind if not shielded.
• Screw/ball‑joint: Pros—secure, precise. Cons—requires drilling; more permanent.
• Clamp/gutter: Pros—no holes. Cons—can loosen; limited on very thick or tapered edges.

Safety Notes

• Use a stable ladder; avoid drilling near electrical or plumbing. For exterior walls, check for hidden utilities.
• Follow local laws on audio/video recording and signage where required.

FAQ

Will this mount fit my Arlo model?

Check whether your camera has a 1/4"‑20 threaded insert or uses Arlo’s magnetic puck. Choose a mount that matches that interface. Doorbells typically require their own bracket.

Can I install without drilling?

Yes—use magnetic mounts (to a pre‑installed plate), adhesive plates on smooth indoor surfaces, or clamp/gutter mounts. For long‑term outdoor use, screw‑in mounts are more reliable.

How long does installation take?

About 10–20 minutes per mount when drilling; 2–5 minutes for magnetic repositions.

Are these mounts weatherproof?

Most outdoor mounts are weather‑resistant. Verify the product’s outdoor rating and use stainless hardware to prevent rust.

Can I move the mount later?

Yes. Unscrew and reinstall with fresh anchors if needed. Seal old holes with exterior caulk or wood filler.